電動扳手主要應用于鋼結構安裝行業，專門安裝鋼結構高強螺栓，高強度螺栓是用來連接鋼結構接點的，通常是用螺栓群的方式出現。
Electric wrenches are mainly used in the steel structure installation industry to install high-strength bolts of steel structures. High strength bolts are used to connect steel structure joints, usually in the form of bolt groups.
高強螺栓可分為扭剪型和大六角型兩種，國標扭剪型高強螺栓為M16、M20、M22、M24四種，非國標的M27、M30兩種；國標大六角高強螺栓為M16、M20、M22、M24、M27、M30等幾種。一般的對于高強螺栓的緊固都要先初緊再終緊，而且每步都需要有嚴格的扭矩要求。
High strength bolts can be divided into torsional shear type and large hexagon type. National standard torsional shear type high strength bolts are M16, M20, M22 and M24, and non-national standard M27 and M30; The national standard large hexagon high-strength bolts are M16, M20, M22, M24, M27, M30, etc. Generally, the tightening of high-strength bolts should be carried out initially and then finally, and strict torque requirements are required for each step.
大六角高強螺栓的初緊和終緊都需要使用定扭矩扳手.故各種電動扳手就是為各種緊固需要而來的。
Constant torque wrench shall be used for initial and final tightening of large hexagon high-strength bolts Therefore, various electric wrenches are provided for various fastening needs.
注意事項
matters needing attention
為高精度產品，使用時提請您注意：
It is a high-precision product. Please pay attention to:
1、使用中應盡量避免磕碰及跌落；
1. Collision and falling shall be avoided during use;
2、嚴禁敲擊及用尖硬物碰撞顯示區域；
2. It is forbidden to knock or hit the display area with sharp hard objects;
3、應平穩施力，嚴禁超過檢測范圍使用；
3. The force shall be applied stably, and it is strictly prohibited to use beyond the detection range;
4、長期停用應將電池取出，以防電池漏液；
4. Take out the battery after long-term shutdown to prevent battery leakage;
5、嚴禁使用強溶劑（如苯、硝基類油）擦拭面板及顯示區域；
5. It is forbidden to use strong solvents (such as benzene and nitro oil) to wipe the panel and display area;
6、嚴防液體進入扳手內，以免損壞電子元件；
6. Prevent the liquid from entering the wrench to avoid damaging the electronic components;
7、當電池電壓降到不能工作時，應更換電池；
7. When the battery voltage drops to the point where it cannot work, the battery shall be replaced;
8、嚴禁隨意拆卸，以免影響精度，如遇問題，請與廠家或銷售商聯系；
8. It is strictly prohibited to disassemble at will to avoid affecting the accuracy. In case of any problem, please contact the manufacturer or seller;
9、使用后應回包裝盒內；
9. Return to the packing box after use;
10、調校方法僅供計量校驗人員參考，其他人員勿動；
10. The adjustment method is only for the reference of the measurement and calibration personnel, and other personnel shall not move;
The above is what the torsion shear electric wrench introduced to you. Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call us for consultation! http://hkystar.com
